Mapout24 obd2 scanner elm 327
OBD2 Bike Scanner, On-Board Diagnostics cable, TVS bike Scanner, KTM bike Scanner Premium Quality long last for A Year
Made from FR series OBD Cable, Made In India, OBD2 Bike Scanner Cable, TVS bike Scanner
Compatible with Bajaj, KTM, TVS, Royal Enfield scooters, and motorcycles (BS 4 It also BS 6 type)
Works with KTM Duke 200 KTM Duke 250 KTM Duke 390 & KTM RC 200 KTM RC 390 (all ktm bs4 only ) Bajaj Pulsar RS200 KTM duke 400 and Bajaj auto Rikshaw
Support BS 4 and BS 6 bike scanners
Supports reading & Clearing fault codes for checking engine lights. (No support for ABS)
Female OBD bike scanner cable.
OBD Connector in Bike Scanner Cable BS4/6 :
OBD2 Bike Scanner Cable BS4/6 is an improvement over OBD-II in both capabilities. It is also standardization.
In OBD2 Bike Scanner Cable BS4/6 OBDII Connector standard specifies the type of diagnostic connector and its pinout, the electrical signaling protocols available, It also messaging format. It also provides a candidate list of vehicle parameters to monitor and how to encode each data. There is a pin in the connector that provides power for the scan tool from the vehicle battery, it also eliminates the need to connect a scan tool to a power source separately.
Universal OBD2 Connector in OBD2 Bike Scanner Cable BS4/6
Female OBD-II connector on a car Female OBD Connector connector pinout – front view. The OBDII specification provides for a standardized hardware interface—the female 16-pin (2×8) J1962 connector. Unlike the OBD-I connector, which was sometimes found, under the hood of the vehicle. It is also required to be within 2 feet (0.61 m) of the steering wheel. used in TVS, KTM, Bajaj & Royal Enfield bike Scanner, TVS bike Scanner, KTM bike, Royal Enfield Scanner
SAE J1962 defines the pinout of the connector as:
The amount of diagnostic information available via OBD2 Bike Scanner Cable BS4/6 OBDII has varied widely since its introduction in the early 1980s versions of onboard vehicle computers.
That is your car telling you there is an issue. If you visit a mechanic, he will use a diagnostic to detect the issue.
To do so, he will connect the OBD2 reader to the OBD2 16-pin connector near the steering wheel.
This lets him read OBD2 codes aka Diagnostic Trouble Codes (DTCs) to review and troubleshoot the issue.
Brand new and high-quality scanner.
Used in TVS, Bajaj, KTM & Royal Enfield bike Scanner.
For connecting your diagnostic interface and your vehicle with OBD-II compliant
Length: About 200cm
OBD-II Plug: 16-pin male to car
Mainly Used for diagnostic OBD2 Bike Scanner Cable BS4/6 Engine company Vehicles
Cable core: 8 Core
OBD Connector Pinout Configuration
|Pin Number||Pin Name||Description|
|1,3,8,9,11,12,13||Blank||These pins are not standard and are vendor-specific. It is also not required for normal communication/interfacing|
|2||SAE J1850 Bus+||This protocol uses Variable Pulse Width and is generally used by GM vehicles. It is also the Bus positive pin of the protocol.|
|10||SAE J1850 Bus-||This protocol uses Variable Pulse Width and is typically used by GM vehicles. it also Buses negative pin of the protocol.|
|4,5||Ground||The ground of the complete system of the Car including the chassis|
|6||ISO15765-4 CAN High||It follows a 2-wire CAN protocol at 1 Mbps speed. It also CAN high Pin|
|14||ISO15765-4 CAN Low||It follows a 2-wire CAN protocol at 1 Mbps speed. It also CAN low the Pin|
|7||ISO 9141 – K Line||It follows asynchronous serial communication protocol, it also Kline Pin|
|8||ISO 9141 – L Line||It follows asynchronous serial communication protocol, It also L line Pin|