Description
Mapout24 obd2 scanner elm 327
OBD2 Bike Scanner OBD cable, TVS bike Scanner,KTM bike Scanner Premium Quality long last for A Year
Made from FR series Indian Cable, Made In India, OBD2 Bike Scanner Cable,TVS bike Scanner
Compatible with Bajaj, KTM, TVS scooters, and motorcycles (BS 4 It also BS 6 type)
Works with KTM Duke 200 KTM Duke 250 KTM Duke 390 & KTM RC 200 KTM RC 390 (all ktm bs4 only ) Bajaj Pulsar RS200 KTM duke 400 and Bajaj auto Rikshaw
Support BS 4 and BS 6 bike scanners like ELM327
Supports reading & Clearing fault code for checking engine light. (No support for ABS)
OBD Female bike scanner cable.
OBD Connector in Bike Scanner Cable BS4/6 :
OBD2 Bike Scanner Cable BS4/6 is an improvement over OBD-II in both capabilities. It is also standardization.
In OBD2 Bike Scanner Cable BS4/6 OBDII Connector standard specifies the type of diagnostic connector and its pinout, the electrical signaling protocols available, It also messaging format. It also provides a candidate list of vehicle parameters to monitor along with how to encode the data for each. There is a pin in the connector that provides power for the scan tool from the vehicle battery, it also eliminates the need to connect a scan tool to a power source separately.
Universal OBD2 Connector in OBD2 Bike Scanner Cable BS4/6
Female OBD-II connector on a car Female OBD Connector connector pinout – front view. The OBDII specification provides for a standardized hardware interface—the female 16-pin (2×8) J1962 connector. Unlike the OBD-I connector, which was sometimes found, under the hood of the vehicle. It is also required to be within 2 feet (0.61 m) of the steering wheel. used in Hero bike Scanner, TVS bike Scanner,KTM bike Scanner
SAE J1962 defines the pinout of the connector as:
The amount of diagnostic information available via OBD2 Bike Scanner Cable BS4/6 OBDII has varied widely since its introduction in the early 1980s versions of onboard vehicle computers.
That is your car telling you there is an issue. If you visit a mechanic, he will use an OBD2 scanner to diagnose the issue.
To do so, he will connect the OBD2 reader to the OBD2 16 pin connector near the steering wheel.
This lets him read OBD2 codes aka Diagnostic Trouble Codes (DTCs) to review and troubleshoot the issue.
Features:
Brand new and high-quality obd2 scanner elm 327.
Used in Hero bike Scanner.
For connecting your diagnostic interface and your vehicle with OBD-II compliant
Length: About 200cm
Weight: 300gm
OBD-II Plug: 16-pin male to car
Mainly Used for diagnostic OBD2 Bike Scanner Cable BS4/6 Engine company Vehicles
Cable core: 8 Core
OBD Connector Pinout Configuration
| Pin Number | Pin Name | Description |
| 1,3,8,9,11,12,13 | Blank | These pins are not standard and are vendor-specific. It is also not required for normal communication/interfacing |
| 2 | SAE J1850 Bus+ | This protocol uses Variable Pulse Width and is normally used by GM vehicles. It also the Bus positive pin of the protocol. |
| 10 | SAE J1850 Bus- | This protocol uses Variable Pulse Width and is normally used by GM vehicles. it also Bus negative pin of the protocol. |
| 4,5 | Ground | The ground of complete system of the Car including chassis |
| 6 | ISO15765-4 CAN High | It follows a 2-wire CAN protocol at 1 Mbps speed. It also CAN high Pin |
| 14 | ISO15765-4 CAN Low | It follows a 2-wire CAN protocol at 1 Mbps speed. It also CAN low Pin |
| 7 | ISO 9141 – K Line | It follows asynchronous serial communication protocol, it also Kline Pin |
| 8 | ISO 9141 – L Line | It follows asynchronous serial communication protocol, It also L line Pin |
