Sale!
(3 customer reviews)

1887

  • Features
  • Brand new and high quality OBD-II to DB15 Male Diagnostic cable.
  • For connecting your diagnostic interface and your vehicle with OBD-II compliant
  • Length: About 200cm
  • Weight: 202 gm
  • OBD-II Plug: 16-pin male to car
  • Mainly Used for diagnostic Force Company Vehicles
Bulk order discount applied automatically in Cart

Description

Mahindra Garuda I Cable ECU Flashing Cable OBD Scanner Cable

Mahindra Garuda I Cable ECU Flashing Cable OBD Scanner Cable garuda i  . also an improvement over OBD-II in both capability and standardization. This Cable OBDII Connector standard specifies the type of diagnostic connector and its pinout, the electrical signaling protocols available, and the messaging format. It also provides a candidate list of vehicle parameters to monitor along with how to encode the data for each. There is also a pin in the connector that provides power for the scan tool from the vehicle battery, which eliminates the need to connect a scan tool to a power source separately.

  • Track and  diagnoses every critical aspect of your
    vehicle with Garuda – a real-time vehicular network
    monitoring, flashing, and diagnosis tool from Global Edge.

 

  • Mahindra Garuda I Cable ECU Flashing Cable OBD Scanner Cable enables you to provide reliable service for vehicles.
    also offers ECU software reprogramming.

Mahindra Garuda I Cable ECU Flashing Cable OBD Scanner Cable Features:

1. Diagnostic solution of vehicle

2. it also Cost-effective

3.It also Supercharged

4.Monitoring Vehicle

5. In Mahindra Garuda I Cable ECU Flashing Cable OBD Scanner Cable OBD II connectivity between vehicle and PC

6. Wide input voltage range (9 – 32 VDC)

7.PC connectivity through USB 2.0 and Wi-Fi

8.Vehicle Battery Read (VBATT)

9.Supports SAE J 2534 and RP 1210 B API for reprogramming and pass-through diagnostics

10. Multi-protocol support – CAN (ISO 11898-2, J2284, J1939, ISO 15765, UDS)

In Mahindra Garuda I Cable ECU Flashing Cable OBD Scanner Cable  Information of OBD2 Connector  :

Mahindra Garuda I Cable ECU Flashing Cable OBD Scanner Cable garuda i. It also has a Female OBD-II connector on a car Female OBD Connector connector pinout – front view The OBDII specification provides for a standardized hardware interface—the female 16-pin (2×8) J1962 connector. Unlike the OBD-I connector, which was sometimes found,  it also under the hood of the vehicle, the OBD-II connector is required to be within 2 feet (0.61 m) of the steering wheel.

In Mahindra Garuda I Cable ECU Flashing Cablee SAE J1962 defines the pinout of the connector as:

The amount of diagnostic information available Mahindra Garuda I OBD2 Male OBDII has also varied widely since its introduction in the early 1980s versions of onboard vehicle computers.

OBD2

That is your car tell If you visit a mechanic, he will use an OBD2 scanner to diagnose the issue.

To do so, he will connect the OBD reader to the OBD2 16 pin connector near the steering wheel.

This lets him read OBD codes aka Diagnostic Trouble Codes (DTCs) to review and troubleshoot the issue.

Features Of Cable:

It is a Brand new and high-quality OBD-II
For connecting your diagnostic interface and your vehicle with OBD-II compliant
Length: About 200cm
Weight: 300gm
OBD-II Plug: 16-pin male to car,Mahindra Garuda I

Pin Number Pin Name Description
1,3,8,9,11,12,13 Blank These pins are not standard and are vendor-specific. It is also not required for normal communication/interfacing
2 SAE J1850 Bus+ Likewise, This protocol uses Variable Pulse Width and is normally used by GM vehicles. This is the Bus positive pin of the protocol.
10 SAE J1850 Bus- This protocol uses Variable Pulse Width and is normally used by GM vehicles. This is the Bus negative pin of the protocol.
4,5 Ground Likewise, The ground of complete system of the Car including chassis
6 ISO15765-4 CAN High follows a 2-wire CAN protocol at 1Mbps speed. It also CAN high Pin
14 ISO15765-4 CAN Low It follows a 2-wire CAN protocol at 1Mbps speed. It also CAN low Pin
7 ISO 9141 – K Line having an asynchronous serial communication protocol. It also Kline Pin
8 ISO 9141 – L Line It also follows the same as pin no 7, this pin is the L line
Information

Brand New & High-Quality Mahindra Garuda I Cable ECU Flashing Cable
For Connecting your Diagnostic Interface and your vehicle with OBD-II Compliant.
Length is about 200 cm.
OBD-II Plug: 16 Pin Male to the car, Mahindra Garuda I
Easy to Use.

3 reviews for Mahindra Garuda I Cable ECU Flashing Cable OBD Scanner Cable

  1. ranimate114 (verified owner)

    Useful Product.

  2. arorasanvi60 (verified owner)

    Useful and value for money.

  3. majumdargautam120 (verified owner)

    Good product, go for it

Only logged in customers who have purchased this product may leave a review.

You may also like…