Sale!

739

  • OBD-II Extension Cable The OBD2 16pin extension cable allows you to connect compatible diagnostic tools with a 16 pin socket
  • A right-angle OBD-II Extension Cable that measures 12 inches long. On one end (the male) the adapter is at a right angle, the other two ends (female) is normal
  • This can be used to plug into an OBD-II compliant vehicle and coupled with OBD-II diagnostic hardware
  • OBD2 16Pin male to a female extension cable
  • High-quality materials give the cable superior flexibility and durability

Description

OBD Splitter OBD YCable scanner obdii for OBDII Splitter Extension Cable

Diagnostic Cable:

OBD Splitter scanner obdii OBD Y Cable is also an improvement over OBD-II in both capability and standardization. This OBD2 Extension cable OBDII Connector standard specifies the type of diagnostic connector and its pinout, the electrical signaling protocols available, and the messaging format. It also provides a candidate list of vehicle parameters to monitor along with how to encode the data for each. There is also a pin in the connector that provides power for the scan tool from the vehicle battery, which eliminates the need to connect a scan tool to a power source separately.

In OBD Splitter Information of Connector  :

It also has a Female OBD-II connector on a car Female OBD Connector connector pinout – front view The OBDII specification provides for a standardized hardware interface—the female 16-pin (2×8) J1962 connector. Unlike the OBD-I connector, which was sometimes found, under the hood of the vehicle, the OBD-II connector is required to be within 2 feet (0.61 m) of the steering wheel.

In Splitter SAE J1962 defines the pinout of the connector as:

The amount of diagnostic information available via Y Splitter OBD-II Cable to OBD-II Female Cable (Round)  OBDII

has varied widely since its introduction in the early 1980s versions of on-board vehicle computers.

OBD2

That is your car telling you there is an issue. If you visit a mechanic, he will use an OBD2 scanner to diagnose the issue.

To do so, he will connect the OBD reader to the OBD2 16 pin connector near the steering wheel.

This lets him read OBD codes aka Diagnostic Trouble Codes (DTCs) to review and troubleshoot the issue.

Features of scanner obd ii:

It is also a Brand new and high-quality OBD-II 
OBD2 Extension cable is connecting your diagnostic interface and your vehicle with OBD-II compliant
Length: About 200cm
Weight: 300gm
OBD-II Plug: 16-pin male to car
Mostly Used for diagnostic Y Splitter OBD-II Cable to OBD-II Female Cable (Round)   Diagnostic Cable Engine company Vehicles
Cable core: 8 Core

In Splitter Obd diagnostic Cable scanner obd ii OBD Connector Pinout Configuration
Pin Number Pin Name Description
1,3,8,9,11,12,13 Blank These pins are not standard and are vendor-specific. It is also not required for normal communication/interfacing
2 SAE J1850 Bus+ Likewise, This protocol uses Variable Pulse Width and is normally used by GM vehicles. This is the Bus positive pin of the protocol.
10 SAE J1850 Bus- This protocol uses Variable Pulse Width and is normally used by GM vehicles. This is the Bus negative pin of the protocol.
4,5 Ground Likewise, The ground of complete system of the Car including chassis
6 ISO15765-4 CAN High It follows a 2-wire CAN protocol at 1Mbps speed. It also CAN high Pin
14 ISO15765-4 CAN Low It follows a 2-wire CAN protocol at 1Mbps speed. It also CAN low Pin
7 ISO 9141 – K Line It follows an asynchronous serial communication protocol. It also Kline Pin
8 ISO 9141 – L Line It also follows the same as pin no 7, this pin is the L line
Information:

 It is also Compatible with diagnostic tools with a 16 pin socket. It is also Universal for all cars with OBD-II Interface. Cable Length: 2 Meter, Cable Core: 8

 

You may also like…